No products in the cart.
1) To install your V1 Tech Custom Graphics Card Backplate, we recommend first removing the graphics
card from your PC.
2) If you opt to use the provided magnets for an easily removable installation, first apply the provided
double-sided tape to one side of the magnets by peeling the protective plastic on the tape and sticking
the tape directly to the magnet. Place the magnets onto the tallest screws* on the back of your graphics
card with the tape facing away from the graphics card.
If a semi-permanent installation is desired, apply the provided double-sided tape directly to the tallest
screws* on the back of your graphics card.
*Note: Ensure that as much surface area is covered as possible, start with the far corners of the graphics card and
evenly distribute magnets/adhesive as you work inward to ensure that as much surface area is covered as possible for
a secure installation.
3) Peel the protective plastic on the other side of the double-sided tape and position the V1 Tech Custom
Graphics Card Backplate directly over the rear of your graphics card (double check to ensure that the
backplate is oriented the correct way by aligning with any SLI or PCIe power cutouts if present. Press
down firmly to secure in place.
Install your graphics card into your system.
3) Peel the protective plastic on the other side of the double-sided tape and position the V1 Tech CustomWith every V1 Tech Addressable RGB Mod Part, we currently include 3 modular methods to power and control your lighting.
Method 1: If you wish to control your V1 Tech RGB component with the included RF remote, simply
connect the SATA RF cable to a SATA power cable from your power supply. Connect the other end of
the SATA RF cable to the LED connector on your V1 Tech RGB component.
Method 1: If you wish to control your V1 Tech RGB component with the included RF remote, simply
Method 2: If you wish to control your V1 Tech RGB component with your motherboard RGB control
software, simply connect the included motherboard 5V cable to an available 3-pin 5V addressable RGB
header* on your motherboard. Connect the other end of the motherboard 5V cable to the LED
connector on your V1 Tech RGB component.
*Note: Please ensure to avoid plugging into a 4-pin 12V non-addressable RGB header, this WILL DAMAGE the LEDs
and could result in damage to your motherboard. Refer to the image below for examples of a 3-pin 5V addressable
RGB header and a 4-pin 12V non-addressable RGB header.
Method 3: If you wish to control your V1 Tech RGB component with the CORSAIR iCUE Software, simply
connect the included CORSAIR iCUE cable to a CORSAIR Commander PRO or Lighting Node PRO.
Connect the other end of the CORSAIR iCUE cable to the LED connector on your V1 Tech RGB
component.
Share your thoughts!
Let us know what you think...
Only logged in customers who have purchased this product may leave a review. Log in now
festrada on Custom Design RGB GPU Backplate –
After some trial and error on my end the guys were finally able to take my request to seal conduit from touch other surface on my motherboard. I fried about 2 led strips and tried to fix it myself. Sent a request to the guys and they help my situation. Turns out I may have been to rough with led on installs. Honestly idk what the heck happened but they helped all the way. Super happy now! Appreciate y’all
(0) (0) Watch Unwatch
sgumbs1994 on Custom Design RGB GPU Backplate –
Shout out to V1tech’s team for making this a smooth, virtually seamless process. Had my order done about a week after making it and I am nothing short of impressed. Thank you once again!
Photo has been removed
(0) (0) Watch Unwatch
poki6041 on Our World RGB GPU Backplate –
the disign is beautiful the colors are awesome ,i have set for a 1080ti g1 gaming and the plastic for the sli ,power cable and the sticker ID (for the graphic card) has been perfectly cutted ,the system of magnet work 🙂
(0) (0) Watch Unwatch
jonathanflorez479 on Custom Design RGB GPU Backplate –
So to begin with, I ordered a custom RGB GPU Backplate a while back and it took about a month for it to arrive but it was all good because when I emailed V1tech they were really transparent and told me since all their products are custom made it would take about a month. Once I actually got my backplate however, I realized it was the wrong size and it was too big for my GPU. Although I didn’t expect much, I sent an email to V1tech explaining the situation and they actually responded asking me for my actual GPU model saying they would send me another backplate this time being the correct size. Not even a week later I get a tracking number saying it’s been delivered to my house and I go outside and sure enough it’s there. This time it fits perfectly into my GPU and I couldn’t be happier with how it turned out. V1tech really came through in helping me and the fact they sent me another backplate free of charge is amazing to me. 10/10 Recommend!
(0) (0) Watch Unwatch
eriksorensen23 on Custom Design RGB GPU Backplate –
I won a custom ARGB back plate on Instagram and I was more excited than a kid on Christmas!
These things are gorgeous, only tip I have to give is if you use an air cooler like I do maybe don’t put your image directly in the middle, kinda offset it so its not blocked by it.
That’s entirely my own lack of planning, these things happen when you get excited!
I did Kaneda from Akira on the iconic motorcycle, also this design is available on Wallpaper engine for a live background if your into cyberpunk/Akira
(0) (0) Watch Unwatch